Accordion M1 MPIO & Power Supply
Mixed-signal-I/O och programmerbar DUT-matning i en handflatestor M1-nod.
- 96 mixed-signal-kanaler (MPIO-96) på sex 20-pins IDC-kontakter, en RGB-LED per kontakt
- 2-kanals programmerbar kraft (Mini-PSU), 5–24 V, 1,5 A per kanal
- 12-bitars ADC/DAC, 0–5 V typiskt
- Kompakt kapsling 120 × 78 × 43 mm, 324 g — Ethernet och WiFi
- Livstidslicenser för Accordion Pilot och Shell ingår
Accordion M1 MPIO & Power Supply är en färdig konfiguration av den kompakta M1-plattformen för PCBA-test, NPI och småskalig produktionstest. Den kombinerar 96 omkonfigurerbara mixed-signal-kanaler med en 2-kanals programmerbar kraftmodul på en nätverksansluten nod. M1-huvudkortet bygger på en Raspberry Pi 4 och är förmonterat med MPIO-96, 6× IDC N-TOP-breakout och Mini-PSU; M.2-platsen är ledig för expansion.
Moduler i konfigurationen
Det här sitter förmonterat i Accordion M1 MPIO & Power Supply — klicka för datablad, specifikationer och anslutningar.
Specifikationer, anslutningar & manual
Allt tekniskt underlag på sidan — expandera en sektion, eller ladda ner hela databladet som PDF. Databladet finns endast på engelska.
Specifications
System
| Parameter | Value | Notes |
|---|---|---|
| Product name | Accordion M1 MPIO & Power Supply | |
| Part number | ESH10000725 | |
| Platform | Accordion M1 (mainboard ESH10000597) | |
| Controller | Raspberry Pi 4, 4 GB | |
| Firmware | Accordion 6.0.0 or later | |
| Power input | USB-C (USB-PD) 20 V, via the bundled 130 W power supply | Use the bundled supply only. |
| Input current, idle | ≤ 0.30 A at 20 V (≤ 6 W) | PSU outputs off. Tested on every unit. |
| Input protection | eFuse, 5 A current limit, overvoltage cut-off above 21 V | |
| Network interface | Ethernet, Wifi | |
| Module slots populated | SO-DIMM (MPIO-96), N-Top (IDC breakout), COMTOP (Mini-PSU) | |
| Module slots free | 1× M.2 | |
| Cooling | Active, one fan, speed-regulated by the Accordion process | Full speed at boot. |
| Enclosure | Hammond 1455K1201BU with E# front and back panels | |
| Dimensions (L × W × H) | 120 × 78 × 43 mm | |
| Weight | 324 g | |
| Compliance | CE, RoHS, REACH |
Included hardware
| Item | Qty | Notes |
|---|---|---|
| Accordion M1 unit | 1 | Pre-configured with the modules below. |
| ESH10000568 — MPIO-96 SPI Module | 1 | SO-DIMM slot. |
| ESH10000355 — 6× IDC N-Top Breakout Module | 1 | N-Top position. |
| ESH10000662 — Mini-PSU | 1 | COMTOP position. |
| USB-C power supply and cable | 1 | 130 W USB-PD supply with a 1 m USB-C cable. |
Lifetime licences for Accordion Shell and Accordion Pilot are included. The Web API, accordionq2 (Python) and AccordionQ2.WebApiClient (.NET) are open clients and need no separate licence.
Channel summary — MPIO-96 (ESH10000568) via IDC (ESH10000355)
| Parameter | Value |
|---|---|
| User channels | 96, bidirectional |
| Modes per channel | Analog input, analog output, pseudo-digital I/O |
| ADC / DAC resolution | 12-bit / 12-bit |
| Analog range | 0–5 V typical (AD5592R 2× mode) |
| Pseudo-digital thresholds | Programmable VL / VH per channel |
| Open-drain / floating-output emulation | Supported (VH < 0 / VL < 0) |
| High-speed acquisition | Supported, via NumericResult |
| Max voltage / current at IDC signal pin | 5 V / 2 A |
| IDC pin-1 / pin-2 rails | 5 V / 20 V, PTC-fused at 0.25 A per connector |
| Connector LEDs | 1 RGB LED per IDC connector, software-controlled |
Power supply — Mini-PSU (ESH10000662)
| Parameter | Value |
|---|---|
| Channels | 2, independent |
| Output voltage | 5–24 V per channel |
| Output current | 1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V |
| Current-limit accuracy | ±5 mA after two-point calibration (0–1.5 A) |
| Load transient (0 → 1.5 A) | ≤ 1 % overshoot, recovery ≤ 5 µs |
| Output stability | ≤ ±0.1 % over 8 h at 24 V / 1 A |
| Readback | Output voltage and current per channel |
Manual
Hardware
Power-on: connect the bundled USB-C supply and the cable to the unit’s power input, connect Ethernet, and apply power (the unit starts at power-up or with the power button, as configured). Boot takes about 1 minute; the fan runs full speed until the Accordion process takes over. The unit is reachable by hostname or DHCP IP. The Mini-PSU outputs are off at boot.
Connecting a fixture: standard 20-pin IDC ribbon from the six connectors to the fixture (check pin-1 orientation); wire the DUT supply leads to the Mini-PSU output connector (VOUT1, VOUT2, GND). Power down before changing wiring.
Software
The unit runs the standard Accordion software — Web API directly, or via Pilot, Shell, accordionq2 (Python), AccordionQ2.WebApiClient (.NET) or TestStand (install commands as for the A2 Lite).
- MPIO channels:
{ModuleIndex}.ESH10000568.MPIO{00–95}, all boot in INPUT mode. - The IDC breakout is passive; its pins are addressed through the MPIO channels.
- Mini-PSU: set voltage and current limit per channel, enable the output, read back output voltage and current.
Pinout
IDC signal connectors (ESH10000355)
| Connector | Signals | MPIO channels |
|---|---|---|
| J1 | DATA[0–15] | MPIO00–MPIO15 |
| J2 | DATA[16–31] | MPIO16–MPIO31 |
| J3 | DATA[32–47] | MPIO32–MPIO47 |
| J4 | DATA[48–63] | MPIO48–MPIO63 |
| J5 | DATA[64–79] | MPIO64–MPIO79 |
| J6 | DATA[80–95] | MPIO80–MPIO95 |
Pin 1 = +5 V, pin 2 = +20 V (both PTC-fused at 0.25 A), pins 3–20 = 16 signals and GND returns.
Mini-PSU output connector (ESH10000662, J2, 4-pin)
| Pin | Signal |
|---|---|
| 1 | VOUT1 |
| 2 | GND |
| 3 | GND |
| 4 | VOUT2 |
Application notes, case & nyheter
Insikter taggade för den här produkten.
Rätt Accordion för din bänk?
Berätta vad du testar så hittar vi rätt konfiguration — eller säger ärligt om en standarduppsättning räcker.