Konfiguration ESH10000754

Accordion M1 Current Source & Supply

Driv och karakterisera strömstyrda laster som lysdioder — åtta mjukvarusatta strömmar med per-kanals återläsning, på en nätverksansluten nod.

  • 8 oberoende konstantströmsutgångar, 0–450 mA per kanal (max 2,4 A totalt)
  • 16-bitars börvärde och 24-bitars strömåterläsning per kanal
  • 2 precisionsmätingångar, 24-bit, single-ended eller differentiell
  • 2-kanals programmerbar kraft (Mini-PSU), 5–24 V, 1,5 A per kanal
  • Livstidslicenser för Accordion Pilot och Shell ingår
Pris på förfrågan
Beskrivning

Accordion M1 Current Source & Supply är en färdig konfiguration av den kompakta M1-plattformen för att driva och övervaka strömstyrda laster — som lysdioder — i PCBA-test, NPI och produktionstest. Den kombinerar åtta oberoende konstantströmsutgångar med per-kanals strömåterläsning, två precisionsmätingångar och en 2-kanals programmerbar kraftmodul på en nätverksansluten nod. M1-huvudkortet bygger på en Raspberry Pi 4; M.2-platsen är ledig för expansion.

Användningsområden
Driva och karakterisera lysdioder och andra strömstyrda laster.
Produktionsfixturer som behöver precisa, mjukvarusatta strömmar med återläsning.
Precisionsmätning av spänning eller shunt-ström vid sidan av strömutgångarna.
Mata DUT:en eller ett ljusbord från samma nod.
Innehåll i systemet

Moduler i konfigurationen

Det här sitter förmonterat i Accordion M1 Current Source & Supply — klicka för datablad, specifikationer och anslutningar.

Teknisk information

Specifikationer, anslutningar & manual

Allt tekniskt underlag på sidan — expandera en sektion, eller ladda ner hela databladet som PDF. Databladet finns endast på engelska.

Specifications

System

Parameter Value Notes
Product name Accordion M1 Current Source & Supply
Part number ESH10000754
Platform Accordion M1 (mainboard ESH10000597)
Controller Raspberry Pi 4, 4 GB
Firmware Accordion 6.0.0 or later
Power input USB-C (USB-PD) 20 V, via the bundled 130 W power supply Use the bundled supply only.
Input protection eFuse, 5 A current limit, overvoltage cut-off above 21 V
Network interface Ethernet, Wifi
Module slots populated SO-DIMM (Precision ADC/DAC), N-Top (Current Source), COMTOP (Mini-PSU)
Module slots free 1× M.2
Cooling Active, one fan, speed-regulated by the Accordion process Full speed at boot.
Enclosure Hammond 1455K1201BU with E# front, top and back panels
Dimensions (L × W × H) 120 × 78 × 43 mm
Weight 324 g
Compliance CE, RoHS, REACH

Included hardware

Item Qty Notes
Accordion M1 unit 1 Pre-configured with the modules below.
ESH10000584 — 8-channel Current Source 1 N-Top position.
ESH10000590 — Precision ADC/DAC Module 1 SO-DIMM slot.
ESH10000662 — Mini-PSU 1 COMTOP position.
microSD card, 32 GB 1 Pre-loaded with the Accordion image.
USB-C power supply + cable 1 130 W, USB-PD, 1 m cable.

Lifetime licences for Accordion Shell and Accordion Pilot are included. The Web API, accordionq2 (Python) and AccordionQ2.WebApiClient (.NET) are open clients.

Current outputs (ESH10000584 with ESH10000590)

Parameter Value Notes
Channels 8, independently controlled
Output current range 0–450 mA per channel
Total output current 2.4 A maximum, continuous, all channels together
Output voltage 0–5 V Depends on load and output current.
Set-point resolution 16-bit
Current readback Per channel, 24-bit ADC
Current sense 0.5 Ω shunt per channel
Off-state leakage < 1 µA
Calibration Two-point (offset + gain) per channel, stored and applied at start-up

Precision measurement inputs (ESH10000590)

Parameter Value Notes
Inputs 2, single-ended or differential
Input range, single-ended 0–5 V Scaled ÷2 to the 2.5 V ADC full scale.
Resolution 24-bit
Sensor supply 5 V, fused at 500 mA On the measurement connector.

Power supply — Mini-PSU (ESH10000662)

Parameter Value
Channels 2, independent
Output voltage 5–24 V per channel
Output current 1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V
Current-limit accuracy ±5 mA after two-point calibration (0–1.5 A)
Readback Output voltage and current per channel

Manual

Hardware

Power-on: connect the bundled USB-C supply and cable, connect Ethernet, and apply power (starts at power-up or with the power button, as configured). Boot takes about 1 minute. All current outputs and the Mini-PSU outputs are off at boot and must be set and enabled in software.

Connecting loads: one 2-pin push-in connector per current channel (OUT+, GND) — wire the load between OUT+ and GND. The 4-pin measurement connector carries 5 V, GND, MEAS+, MEAS−. The Mini-PSU output connector carries VOUT1, VOUT2, GND. Keep the sum of all channel currents at or below 2.4 A. Power down before changing wiring.

Software

Standard Accordion software — Web API, Pilot, Shell, accordionq2, AccordionQ2.WebApiClient or TestStand (install commands as for the A2 Lite).

  • Set each channel’s current, enable it, and read back the measured current.
  • Calibration is two-point per channel; run it from Pilot or the API.
  • Mini-PSU: set voltage and current limit per channel, then enable.

Pinout

Current outputs (8 × 2-pin, Phoenix Contact 1843606)

Pin Signal Description
1 OUT+ Current output, positive terminal
2 GND Common ground

Measurement connector (4-pin, Phoenix Contact 1881574)

Pin Signal Description
1 5V 5 V supply, fused at 500 mA
2 GND Ground
3 MEAS+ Single-ended input / differential positive
4 MEAS− Single-ended input / differential negative

Maximum voltage on the measurement pins is 5 V.

Mini-PSU output connector (ESH10000662, 4-pin)

Pin Signal
1 VOUT1
2 GND
3 GND
4 VOUT2
Relaterat

Application notes, case & nyheter

Insikter taggade för den här produkten.

Rätt Accordion för din bänk?

Berätta vad du testar så hittar vi rätt konfiguration — eller säger ärligt om en standarduppsättning räcker.

Boka en demo av Probe

Visa oss ditt kort — vi granskar det och går igenom fynden tillsammans.

Föredrar du att mejla? info@esharp.se