Configuration ESH10000754

Accordion M1 Current Source & Supply

Drive and characterise current-driven loads like LEDs — eight software-set currents with per-channel readback, on a networked node.

  • 8 independent constant-current outputs, 0–450 mA per channel (max 2.4 A total)
  • 16-bit setpoint and 24-bit current readback per channel
  • 2 precision measurement inputs, 24-bit, single-ended or differential
  • 2-channel programmable power (Mini-PSU), 5–24 V, 1.5 A per channel
  • Lifetime licences for Accordion Pilot and Shell included
Price on request
Description

Accordion M1 Current Source & Supply is a ready-made configuration of the compact M1 platform for driving and monitoring current-driven loads — such as LEDs — in PCBA test, NPI and production test. It combines eight independent constant-current outputs with per-channel current readback, two precision measurement inputs and a 2-channel programmable power module on a networked node. The M1 main board is based on a Raspberry Pi 4; the M.2 slot is free for expansion.

Use cases
Driving and characterising LEDs and other current-driven loads.
Production fixtures that need precise, software-set currents with readback.
Precision measurement of voltage or shunt current alongside the current outputs.
Powering the DUT or a light table from the same node.
System contents

Modules in the configuration

This comes pre-assembled in Accordion M1 Current Source & Supply — click for the datasheet, specifications and connections.

Technical information

Specifications, connections & manual

All technical material on the page — expand a section, or download the whole datasheet as a PDF.

Specifications

System

Parameter Value Notes
Product name Accordion M1 Current Source & Supply
Part number ESH10000754
Platform Accordion M1 (mainboard ESH10000597)
Controller Raspberry Pi 4, 4 GB
Firmware Accordion 6.0.0 or later
Power input USB-C (USB-PD) 20 V, via the bundled 130 W power supply Use the bundled supply only.
Input protection eFuse, 5 A current limit, overvoltage cut-off above 21 V
Network interface Ethernet, Wifi
Module slots populated SO-DIMM (Precision ADC/DAC), N-Top (Current Source), COMTOP (Mini-PSU)
Module slots free 1× M.2
Cooling Active, one fan, speed-regulated by the Accordion process Full speed at boot.
Enclosure Hammond 1455K1201BU with E# front, top and back panels
Dimensions (L × W × H) 120 × 78 × 43 mm
Weight 324 g
Compliance CE, RoHS, REACH

Included hardware

Item Qty Notes
Accordion M1 unit 1 Pre-configured with the modules below.
ESH10000584 — 8-channel Current Source 1 N-Top position.
ESH10000590 — Precision ADC/DAC Module 1 SO-DIMM slot.
ESH10000662 — Mini-PSU 1 COMTOP position.
microSD card, 32 GB 1 Pre-loaded with the Accordion image.
USB-C power supply + cable 1 130 W, USB-PD, 1 m cable.

Lifetime licences for Accordion Shell and Accordion Pilot are included. The Web API, accordionq2 (Python) and AccordionQ2.WebApiClient (.NET) are open clients.

Current outputs (ESH10000584 with ESH10000590)

Parameter Value Notes
Channels 8, independently controlled
Output current range 0–450 mA per channel
Total output current 2.4 A maximum, continuous, all channels together
Output voltage 0–5 V Depends on load and output current.
Set-point resolution 16-bit
Current readback Per channel, 24-bit ADC
Current sense 0.5 Ω shunt per channel
Off-state leakage < 1 µA
Calibration Two-point (offset + gain) per channel, stored and applied at start-up

Precision measurement inputs (ESH10000590)

Parameter Value Notes
Inputs 2, single-ended or differential
Input range, single-ended 0–5 V Scaled ÷2 to the 2.5 V ADC full scale.
Resolution 24-bit
Sensor supply 5 V, fused at 500 mA On the measurement connector.

Power supply — Mini-PSU (ESH10000662)

Parameter Value
Channels 2, independent
Output voltage 5–24 V per channel
Output current 1.5 A continuous per channel up to 20 V output; about 30 W per channel above 20 V
Current-limit accuracy ±5 mA after two-point calibration (0–1.5 A)
Readback Output voltage and current per channel

Manual

Hardware

Power-on: connect the bundled USB-C supply and cable, connect Ethernet, and apply power (starts at power-up or with the power button, as configured). Boot takes about 1 minute. All current outputs and the Mini-PSU outputs are off at boot and must be set and enabled in software.

Connecting loads: one 2-pin push-in connector per current channel (OUT+, GND) — wire the load between OUT+ and GND. The 4-pin measurement connector carries 5 V, GND, MEAS+, MEAS−. The Mini-PSU output connector carries VOUT1, VOUT2, GND. Keep the sum of all channel currents at or below 2.4 A. Power down before changing wiring.

Software

Standard Accordion software — Web API, Pilot, Shell, accordionq2, AccordionQ2.WebApiClient or TestStand (install commands as for the A2 Lite).

  • Set each channel’s current, enable it, and read back the measured current.
  • Calibration is two-point per channel; run it from Pilot or the API.
  • Mini-PSU: set voltage and current limit per channel, then enable.

Pinout

Current outputs (8 × 2-pin, Phoenix Contact 1843606)

Pin Signal Description
1 OUT+ Current output, positive terminal
2 GND Common ground

Measurement connector (4-pin, Phoenix Contact 1881574)

Pin Signal Description
1 5V 5 V supply, fused at 500 mA
2 GND Ground
3 MEAS+ Single-ended input / differential positive
4 MEAS− Single-ended input / differential negative

Maximum voltage on the measurement pins is 5 V.

Mini-PSU output connector (ESH10000662, 4-pin)

Pin Signal
1 VOUT1
2 GND
3 GND
4 VOUT2
Related

Application notes, cases & news

Insights tagged for this product.

The right Accordion for your bench?

Tell us what you're testing and we'll find the right configuration — or say honestly if a standard setup is enough.

Book a demo of Probe

Show us your board — we review it and go through the findings together.

Prefer to email? info@esharp.se