Module ESH10000662

Mini-PSU

Precise, programmable power without analogue control lines — two independent buck-boost channels over I²C.

  • 2 independent channels, 5–24 V, 1.5 A per channel (approx. 30 W/channel above 20 V)
  • Buck-boost — works both above and below the output setpoint
  • Voltage and current limit set via DAC over I²C; output voltage read via ADC
  • Current-limit linearity ≤ ±0.1% of full scale (1.5 A)
  • Hardware UVLO/OVLO and output OVP protect converter and load
Price on request
Description

ESH10000662 is a 2-channel programmable buck-boost power module in Comtop form factor. Each channel provides an independent, regulated output voltage with a programmable constant-current limit. Voltage and current limit are set via an onboard DAC over I²C, and the actual output voltage is read via an ADC on the same bus — with no analogue control lines per channel. The buck-boost topology works both above and below the setpoint, and hardware protection (UVLO/OVLO/OVP) protects the converter and load.

Use cases
Programmable power in Accordion-based test systems.
Voltage margin testing and current cycling of DUTs.
Constant-current load simulation.
Multi-rail supply in automated production fixtures.
Technical information

Specifications, connections & manual

All technical material on the page — expand a section, or download the whole datasheet as a PDF.

Specifications

Parameter Value
Form factor Comtop Module
Output channels 2 (independent)
Output voltage range 5–24 V per channel
Max continuous output current 1.5 A per channel up to 20 V; about 30 W/channel above 20 V
Output topology Buck-boost
Control interface I²C
Voltage setpoint (VSET) DAC, up to 4.79 V → 24 V (gain ≈ 5.01 V/V)
Current-limit setpoint (ISET) DAC, 0.20–4.56 V → 0–1.5 A
Current-limit linearity ≤ ±0.1 % of full scale (1.5 A)
Output voltage monitoring ADC per channel (resistor divider)
Current monitoring Analog ISMON per channel
Switching frequency ~980 kHz
UVLO (rising / falling) 16.7 V / 14.7 V
OVLO (rising / falling) 29.6 V / 28.7 V
Output OVP threshold 29.4 V
Load transient (0→1.5 A) ≤ 1 % overshoot; recovery ≤ 5 µs
Long-term stability ≤ ±0.1 % over 8 h at 24 V / 1 A
Buck-boost controller LT3942
DAC/ADC AD5593R (8-channel, 0–5 V FS)
GPIO expander PI4IOE5V6416 (I²C, 0x20)

Manual

Architecture

Each channel uses an LT3942 4-switch buck-boost controller at ~980 kHz, transitioning between buck, buck-boost and boost based on VIN/VOUT. Hardware UVLO (16.7 V rising) and OVLO (29.6 V rising) protect against input excursions; FB OVP at 29.4 V protects the load. An AD5593R provides DAC channels (VSET, ISET) and ADC channels (VMON, ISMON) over I²C; a PI4IOE5V6416 GPIO expander (0x20) handles EN1n/EN2n and PWM1n/PWM2n.

Voltage & current control

Output voltage is set via the VSET DAC (max 4.79 V → 24.0 V, gain ≈ 5.01 V/V). Constant-current limit is set via the ISET DAC (active 0.20–4.56 V → 0–1.5 A, DAC step ≈ 0.42 mA; 50 mΩ sense). The LT3942 enters constant-current mode automatically when output current reaches the programmed threshold.

Monitoring, enable & protection

VMON1/2 and ISMON1/2 are read back over I²C via the AD5593R ADC. Each channel has an active-low enable (EN1n/EN2n) and active-low PWM (PWM1n/PWM2n) through the GPIO expander — write the output register before setting pin direction to avoid glitching the enable lines. Protections: input UVLO/OVLO, output OVP (29.4 V), soft-start (~1.76 ms), keep-running fault mode (no latch-off).


Pinout

J2 — Output connector (Phoenix, 4-pin)

Pin Signal Description
1 VOUT1 Channel 1 output
2 GND Output ground
3 GND Output ground
4 VOUT2 Channel 2 output
Related

Application notes, cases & news

Insights tagged for this product.

The right Accordion for your bench?

Tell us what you're testing and we'll find the right configuration — or say honestly if a standard setup is enough.

Book a demo of Probe

Show us your board — we review it and go through the findings together.

Prefer to email? info@esharp.se