Module ESH10000582

USB PD 100W PSU

One USB-C charger, any fixed voltage — consolidate several power adapters into one source, 9–56 V, up to 100 W.

  • Powered by a standard USB-C PD charger (5–20 V in), boost to 9–56 V out
  • Up to 100 W (requires a 100 W charger; limited by the input power)
  • Output voltage via DIP — 9/12/15/24/48/56 V; typical efficiency ~95%
  • Output-voltage accuracy ±1% of setpoint; front LEDs for in/out/temp
  • Hardware on/off via CTRL; over-temperature protection (trip 85 °C)
Price on request
Description

ESH10000582 is a compact 100 W programmable boost supply powered entirely by an ordinary USB-C PD charger. It takes a negotiated USB PD input voltage (5–20 V) and delivers a selectable DC output of 9–56 V — good for replacing several fixed power adapters with a single USB-C source. Housed in a Hammond 1455C801 (80 × 54 × 23 mm); input and output voltage are set with internal DIP switches, and front LEDs show status for input, output and temperature.

Use cases
Replacing several fixed power adapters with a USB-C PD source in the field, lab or production.
Powering embedded systems, sensors, motors or industrial devices that need e.g. 24 V or 48 V.
Bench supply for prototyping and verification where only USB-C is available.
Hardware-controlled power sequencing via CTRL in automated test rigs.
Technical information

Specifications, connections & manual

All technical material on the page — expand a section, or download the whole datasheet as a PDF.

Specifications

Parameter Value Notes
Input interface USB-C (USB PD) PD negotiation required
Input voltage options 5, 9, 12, 15, 20 V DIP-switch selectable
Output voltage options 9, 12, 15, 24, 48, 56 V DIP-switch selectable
Max output power 100 W Requires a 100 W USB PD charger; limited to input power
Topology Boost Vout must be greater than Vin
Efficiency (typical) ~95 %
Output voltage accuracy ±1 % of setpoint
Power-good threshold ±5 % of setpoint Out LED red outside this window
Enclosure Hammond 1455C801 80 × 54 × 23 mm
Compliance CE, RoHS, REACH

Thermal protection

Event Threshold Behaviour
Overtemperature trip 85 °C Output disabled; OT LED red
Overtemperature recovery 75 °C Output resumes or returns to standby (see Disable Standby)

Maximum output current depends on the negotiated input tier and chosen output voltage (≈95 % efficiency). For full 100 W output the charger must negotiate 20 V at 5 A. A 5 V input is not sufficient for Vout > 15 V.


Manual

Initial setup

  1. Open the enclosure and set the three DIP-switch banks: Vin, Vout, and Disable Standby.
  2. Connect the load to the Power-out terminal (front).
  3. Connect a USB-C PD charger rated for the desired input tier (100 W charger for full output).
  4. If Disable Standby is OFF, press the Power button to enable the output.

This is a boost converter — Vout must always be set greater than Vin.

Front panel

  • In LED — green: USB PD negotiation succeeded; red: negotiation failed.
  • Out LED — blue: standby; green: active and within ±5 %; red: active but out of tolerance.
  • OT LED — off: normal; red: >85 °C, output disabled.
  • Power button — toggles between standby and output-enabled.

CTRL interface

The rear CTRL connector allows hardware-controlled output disable: shorting the two pins disables the output, removing the short re-enables it (subject to Disable Standby / standby state). Pin 1 is pulled up to 3.3 V via 10 kΩ; a 70 V series diode allows open-drain drivers above 3.3 V.


Connectors

Power out (rear) — 2-pin pluggable terminal block, 5.0 mm (DB2ERC-5.0-2P-GN)

Pin Signal Description
1 V out Positive output
2 GND Return / ground

CTRL (rear) — 2-pin header, 2.54 mm

Pin Signal Description
1 CTRL Control input (pull to GND to disable)
2 GND Reference ground

USB in (rear)

USB Type-C receptacle. USB PD negotiation runs automatically at power-on based on the Vin DIP setting. Use a USB PD-compliant charger.

Related

Application notes, cases & news

Insights tagged for this product.

The right Accordion for your bench?

Tell us what you're testing and we'll find the right configuration — or say honestly if a standard setup is enough.

Book a demo of Probe

Show us your board — we review it and go through the findings together.

Prefer to email? info@esharp.se